www.gagemaker.com (USA) Phone:713-472-7360 Address 712E. Southmore Avenue Pasadena, TX77502 USA
  www.gagemaker.ru (Russia) Тел.: 8(499)5026625, (499)5018873, РФ, г. Москва, ул. Хабарова 2, e-mail: gagemaker@yandex.ru, info@gagemaker.ru
Прямые поставки сертифицированной продукции Gagemaker из США в РФ   

Специализированные приборы
Speciality Items

Coupling Alignment
Coupling Alignment

A coupling is aligned when the axis of each threaded taper cone is properly oriented to the other. If either or both axes are not correctly orientated, the coupling is misaligned and must be scrapped as it is out of specification. To ensure the threads on both ends of the coupling are properly aligned, Gagemaker recommends inspecting with our coupling alignment gage. CA-9001, CA-9001-M.



Нутромер для внутренних измерений диаметра
Internal Deep Reach Bore

T Internal deep reach bore gages allow the difficult measuring of pitch diameter deep inside a small diameter product. For measuring larger deep diameters, contact point extension rods can be attached. The DB series of gages are our internal deep reach bore gages. One set of contact points and one set of extension rods are included. DB-1800 (18" 457,2мм), DB-2400 (24" 609,6мм).




Глубина неровностей
Pit Depth

Прибор PD-3000 Серия применяется для определения глубины неровностей на цилиндрических поверхностях, К нему подходят различные виды насадок с помощью которых можно проверять высоту зуба резьбы или глубину канавки.

PD-3000 Серия подразделяется на различные формы базы прибора:
PD-3003 стандартная .250" (6,35мм)
PD-3004 стандартная .450" (11,43мм)
PD-3005 плоская .450" (11,43мм)
PD-3006 удлиненная 6" плоская .450" (11,43мм)
PD-3007 удлиненная 6" ласточкин хвост.450" (11,43мм)

Power Tight Make-up
Power Tight Make-up

According to API, power tight is when “a threaded connection has been fully made up by mechanical means using power tongs or a screw-on machine”. The Power Tight Make-up Gage, PT-4000, adjusts to determine the proper make-up location of API couplings. The PT-4000 measure both coupling length and the make up length.

This ensures that the pin and the coupling have made up at the proper distance, or rather that the pin has gone deep enough into the coupling.








According to ASME B 1.7-2006, standoff is the axial distance between specified reference points on external and internal taper threaded members or gages when assembled with a specified torque or under specified conditions.

More simply though, API defines standoff as the distance between faces of one gage to another or when mated, the distance between the gage face and the product reference plane.


For API products, standoff is a required inspection.

However, a particular inspection method is not defined. For the best results with rotary shouldered connections, Gagemaker recommends using one of our standoff gages from the ST-7000 Series.




For standoff inspection on rotary shouldered connections, the ST-7001 is for pins and the ST-7002 is for boxes. The ST-7001 measures variation in ring and plug gage standoff on rotary shouldered connections.

The ST-7001 is set with the supplied setting standard.
The ST-7002 is set on any qualified surface.


Wall Thickness Gages
Wall Thickness Gages

The WT-9000 series of gages measures wall thickness at specific distances from the end of the pipe. Specify the distance from the end of the pipe to the measuring plane when ordering.


www.gagemaker.com (USA) Phone: 713-472-7360 Address 712E. Southmore Avenue Pasadena, TX77502 USA
www.gagemaker.ru (Russia) Тел.: 8(499) 502 66 25, (499) 501 88 73, РФ, г. Москва, ул.Хабарова 2

При использовании информации с сайта www.gagemaker.ru ссылка обязательна